This website uses cookies. By clicking Accept, you consent to the use of cookies. Click Here to learn more about how we use cookies.
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
- Revenera Community
- :
- InstallShield
- :
- InstallShield Forum
- :
- Re: Unable to Capture results properly from CMD line parameter executions by LaunchApp
Subscribe
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Subscribe
- Mute
- Printer Friendly Page
- Mark as New
- Subscribe
- Mute
- Permalink
- Report Inappropriate Content
‎Jul 14, 2017
07:09 AM
Unable to Capture results properly from CMD line parameter executions by LaunchApp
Hello Friends,
I am facing problem in fetching the return result properly from LaunchAppAndWait where i am trying to execute the CMD command.
When I execute the code, the ErrorLogTest.txt file is getting created with all the outputs/errors properly. BUT
The szResult in my code is returning "The specified file path cannot be found" and nResult is -2. Definitely its not correct return status.
This happens in the case when the group is already present and it writes this message in the log file "The specified local group already exists".
In case when the group doesnt exist, it creates the group and szResult shows "Operation completed successfully" and the same gets written in the log file too.
My observation shows that because of the double quotes due to /C, Installer is somehow thinking the entire command as some kind of file path. You can verify this by printing the szCommand in a MessageBox.
Is there any problem with my code? I want to get correct result in szResult in both error and success cases. How to get it. I know i can get it from the logfile that i am printing but i want to get directly from szResult without having to read the file repeatedly.
Any help guys...please. Thanks
I am facing problem in fetching the return result properly from LaunchAppAndWait where i am trying to execute the CMD command.
function CreateGroup()
STRING szGroup,szTempFile, szTempFolderPath;
STRING szProgram,szCmdLine, szResult, szComment;
NUMBER nResult;
begin
szProgram =SystemFolder^"cmd.XXX"; //Need to remove executable format as forum not allowing the post to submit. IGNORE IT!!
szTempFile = "ErrorLogTest.txt";
szTempFolderPath = TempFolder ^ szTempFile;
szGroup = "TestGroup";
szComment = "TestGroup";
szCmdLine = "%/C \"NET LOCALGROUP \""+szGroup+"\" "+"\/comment\:\""+szComment+"\" \/add >"+szTempFolderPath+" 2>&1\"";
MessageBox(szCmdLine,INFORMATION);
//Launch the program with the parameters
if (LaunchAppAndWait(szProgram, szCmdLine, LAAW_OPTION_WAIT|LAAW_OPTION_HIDDEN) < 0) then
MessageBox("Failed to execute the program", INFORMATION);
else
nResult = LAAW_PARAMETERS.nLaunchResult;
szResult = FormatMessage(nResult);
//if the launched applications returns an error, it will be logged
if (nResult != 0) then
SprintfMsiLog("The returned error is:\"" + szResult + "\"");
else
SprintfMsiLog("The returned information is:\"" + szResult + "\"");
endif;
MessageBox("Program Executed:"+szResult, INFORMATION);
endif;
end;
When I execute the code, the ErrorLogTest.txt file is getting created with all the outputs/errors properly. BUT
The szResult in my code is returning "The specified file path cannot be found" and nResult is -2. Definitely its not correct return status.
This happens in the case when the group is already present and it writes this message in the log file "The specified local group already exists".
In case when the group doesnt exist, it creates the group and szResult shows "Operation completed successfully" and the same gets written in the log file too.
My observation shows that because of the double quotes due to /C, Installer is somehow thinking the entire command as some kind of file path. You can verify this by printing the szCommand in a MessageBox.
Is there any problem with my code? I want to get correct result in szResult in both error and success cases. How to get it. I know i can get it from the logfile that i am printing but i want to get directly from szResult without having to read the file repeatedly.
Any help guys...please. Thanks
(9) Replies
- Mark as New
- Subscribe
- Mute
- Permalink
- Report Inappropriate Content
‎Jul 14, 2017
08:49 AM
Hi,
I just took a look at one of my projects and happen to have similar code. Here is mine for reference. It is a bit different than yours in that I only write to file if command succeeds and I only write to file if output contains what I am looking for.:
Here is your code. Need to be careful with placement of +.
Try this (untested):
I just took a look at one of my projects and happen to have similar code. Here is mine for reference. It is a bit different than yours in that I only write to file if command succeeds and I only write to file if output contains what I am looking for.:
szCmdLine = "/C net localgroup administrators | find /I \"" + szAccount + "\" && echo(>" + szTempFileSpec;
Here is your code. Need to be careful with placement of +.
szCmdLine = "%/C \"NET LOCALGROUP \""+szGroup+"\" "+"\/comment\:\""+szComment+"\" \/add >"+szTempFolderPath+" 2>&1\"";
Try this (untested):
szCmdLine = "/C NET LOCALGROUP + \" + szGroup + "\ \"/comment:\" + szComment + "\ "\/add >\" + szTempFolderPath + \" 2>&1\"";
- Mark as New
- Subscribe
- Mute
- Permalink
- Report Inappropriate Content
‎Jul 17, 2017
07:38 AM
rguggisberg wrote:
Hi,
I just took a look at one of my projects and happen to have similar code. Here is mine for reference. It is a bit different than yours in that I only write to file if command succeeds and I only write to file if output contains what I am looking for.:
szCmdLine = "/C net localgroup administrators | find /I \"" + szAccount + "\" && echo(>" + szTempFileSpec;
Here is your code. Need to be careful with placement of +.
szCmdLine = "%/C \"NET LOCALGROUP \""+szGroup+"\" "+"\/comment\:\""+szComment+"\" \/add >"+szTempFolderPath+" 2>&1\"";
Try this (untested):
szCmdLine = "/C NET LOCALGROUP + \" + szGroup + "\ \"/comment:\" + szComment + "\ "\/add >\" + szTempFolderPath + \" 2>&1\"";
Hi,
Its not working man, whatever you asked me to try. In fact it threw lot of compile errors for improper use of "" or /. I corrected them and then tried to run and it threw error: "Invalid function"
Any more suggestions?
Thanks
- Mark as New
- Subscribe
- Mute
- Permalink
- Report Inappropriate Content
‎Jul 18, 2017
08:50 AM
I will test and post when I get time.
- Mark as New
- Subscribe
- Mute
- Permalink
- Report Inappropriate Content
‎Jul 18, 2017
08:52 AM
rguggisberg wrote:
I will test and post when I get time.
Thanks Bro 🙂
- Mark as New
- Subscribe
- Mute
- Permalink
- Report Inappropriate Content
‎Jul 18, 2017
11:55 AM
Hi dinesh.redhawk,
These command lines are tricky and I always start simple and add to it. I should have tested before posting... but that takes time 😞
You probably know that you can compile your InstallScript code without doing a full build (which can take quite a bit of time). Just right click on your Setup.rul (or similar) and click 'Compile'. This only takes a few seconds. Build when all compile errors are resolved. The following command line works for me:
These command lines are tricky and I always start simple and add to it. I should have tested before posting... but that takes time 😞
You probably know that you can compile your InstallScript code without doing a full build (which can take quite a bit of time). Just right click on your Setup.rul (or similar) and click 'Compile'. This only takes a few seconds. Build when all compile errors are resolved. The following command line works for me:
szCmdLine = "/C NET LOCALGROUP " + szGroup + "\ /comment:\"" + szComment + "\" /add >\"" + szTempFolderPath + "\" 2>&1";
- Mark as New
- Subscribe
- Mute
- Permalink
- Report Inappropriate Content
‎Jul 19, 2017
01:17 AM
rguggisberg wrote:
Hi dinesh.redhawk,
These command lines are tricky and I always start simple and add to it. I should have tested before posting... but that takes time 😞
You probably know that you can compile your InstallScript code without doing a full build (which can take quite a bit of time). Just right click on your Setup.rul (or similar) and click 'Compile'. This only takes a few seconds. Build when all compile errors are resolved. The following command line works for me:
szCmdLine = "/C NET LOCALGROUP " + szGroup + "\ /comment:\"" + szComment + "\" /add >\"" + szTempFolderPath + "\" 2>&1";
Ok, i tried this and its giving me the same result. Now lets jump to the 2nd part of my question i.e. the result of szResult. [Please refer to my first post, code is there]
The szResult in my code is returning "The specified file path cannot be found" and nResult is -2. Definitely its not correct return status.
This happens in the case when the group is already present and it writes this message in the log file "The specified local group already exists".
In case when the group doesn't exist, it creates the group and szResult shows "Operation completed successfully" and the same gets written in the log file too.
My observation says that because of the double quotes due to /C, Installer is somehow thinking the entire command as some kind of file path. You can verify this by printing the szCommand in a MessageBox.
Whats your thoughts on this?
Thanks
- Mark as New
- Subscribe
- Mute
- Permalink
- Report Inappropriate Content
‎Jul 19, 2017
07:59 AM
Keep in mind that nResult only contains the result (Success/Fail) of the LaunchAppAndWait. It definitely does NOT contain the result of your NET LOCALGROUP command. You need to parse the file that you piped the results to to get that.
- Mark as New
- Subscribe
- Mute
- Permalink
- Report Inappropriate Content
‎Jul 19, 2017
08:17 AM
rguggisberg wrote:
Keep in mind that nResult only contains the result (Success/Fail) of the LaunchAppAndWait. It definitely does NOT contain the result of your NET LOCALGROUP command. You need to parse the file that you piped the results to to get that.
My research says another thing - If you pass LAAW_PARAMETERS as parameters to LaunchAppandWait, then nResult will contain the results of the launched application i.e. in my case NET LOCALGROUP.
Below is the explanation from Flexera Help:
"
If the application cannot be launched, the nLaunchResult member contains the result of calling GetLastError after the CreateProcess call. If LaunchApp, LaunchAppAndWait, or LaunchApplication is successful and the LAAW_OPTION_WAIT option was specified, the nLaunchResult member contains the return code of the launched application."
- Mark as New
- Subscribe
- Mute
- Permalink
- Report Inappropriate Content
‎Jul 19, 2017
08:49 AM
dinesh_redhawk wrote:
Ok, i tried this and its giving me the same result. Now lets jump to the 2nd part of my question i.e. the result of szResult. [Please refer to my first post, code is there]
The szResult in my code is returning "The specified file path cannot be found" and nResult is -2. Definitely its not correct return status.
This happens in the case when the group is already present and it writes this message in the log file "The specified local group already exists".
In case when the group doesn't exist, it creates the group and szResult shows "Operation completed successfully" and the same gets written in the log file too.
My observation says that because of the double quotes due to /C, Installer is somehow thinking the entire command as some kind of file path. You can verify this by printing the szCommand in a MessageBox.
Whats your thoughts on this?
Thanks
Not sure what "Same result" is. Does it compile successfully? I used the command line I posted and it works as expected. MsgBox shows:
szCmdLine=/C NET LOCALGROUP UserName /comment:"My Comment" /add >"MyPath\MyFileName.txt" 2>&1
As far as the nResult thing.... You may be right, but based on past experience I am not convinced. I have not seen it work that way.... maybe it should. Do you have any other options specified besides LAAW_OPTION_WAIT ?
![](/skins/images/8C9D13A71C7F7695F3262372C0172D68/responsive_peak/images/icon_anonymous_message.png)